退火工艺对搅拌摩擦加工镁合金微观组织和显微硬度的影响

采用搅拌摩擦加工(Friction stir processing,FSP)技术对AZ31镁合金进行加工,通过采取不同温度及保温时间的退火工艺,研究了FSP镁合金在退火过程中的微观组织演变过程及硬度变化规律。结果表明,FSP成功制备了细晶AZ31镁合金,其平均晶粒尺寸细化程度达54.9%。当退火温度在200～300 ℃时,加工区(SZ)晶粒尺寸较为稳定,且组织发生不同程度的均匀化和细化;当温度超过300 ℃时,加工区晶粒互相吞噬而快速长大。在退火温度较低、短时间保温时热影响区(HAZ)组织变化不明显,而延长保温时间或者升高温度,HAZ区组织会迅速细化、均匀化;当退火温度超过300 ℃时,再结晶会在短时间内完成,随后晶粒继续长大。在300 ℃下保温60 min为最优退火工艺,可使SZ、HAZ组织分别细化10.9%、35.6%。     

冷处理和深冷处理在渗碳齿轮件中的应用

通过分析18Cr2Ni4WA和20Cr2Ni4A钢的冷处理和深冷处理工艺过程,经试验确定合理的工艺参数后应用于渗碳齿轮件的实际生产中。结果表明,冷处理和深冷处理后渗碳层表面硬度提高3~5 HRC,并可有效增加淬硬层深度。     

17-4PH不锈钢480 ℃时效组织的动态演变规律

将17-4PH不锈钢锻棒固溶处理后油冷,然后选择在最佳的时效温度480 ℃时效保温0～5 h后空冷。通过光学显微镜(OM)、超景深显微镜、XRD、显微硬度仪等测试方法观察固溶、时效过程的组织演变和分析其沉淀硬化机理;采用电阻仪间接测试ε-Cu相动态时效析出过程对电阻的影响;并利用摩擦磨损试验机测试其耐磨性能。研究发现:17-4PH不锈钢固溶和时效过程没有残留奥氏体和逆转变奥氏体出现,热处理后出现板条状和块状两种马氏体形态,板条状马氏体硬度高于块状马氏体,随着时效时间的延长,两种马氏体硬度同步上升,时效析出明显提高了固溶态组织的硬度;时效2.0～2.5 h附近强化效果和耐磨性能最弱,可能与ε-Cu 相长大及与位错交互作用有关;硬度随时效时间的变化趋势与电阻正好相反。     

B对FeCoCrNiSiBx高熵合金激光熔覆层组织和硬度的影响

采用激光熔覆制备了FeCoCrNiSiB_x高熵合金熔覆层,利用光学显微镜、扫描电镜、X射线衍射仪和显微硬度计研究微量硼元素(摩尔比x=0、0.02、0.04、0.06、0.08)对FeCoCrNiSiB_x高熵合金熔覆层组织和硬度的影响。结果表明:无B高熵合金涂层组织主要为胞状晶。B的添加会促进枝晶的生成,逐渐形成鱼骨状树枝晶,但过量的B会破坏枝晶完整性,形成蠕虫状晶。此外,高熵合金熔覆层组织为FCC和BCC双相结构,B元素的添加会形成大量0.1~2.6 μm的Cr₂B第二相,有助于提高熔覆层硬度,其中x=0.06时激光熔覆层的硬度最高,约为537 HV0.2。     

GH3535合金的表面改性

GH3535镍基合金的硬度仅为200HV左右,不能达到超高温熔盐液下轴承要求的400HV以上的硬度。为此,对GH3535合金进行了不同的表面改性处理,包括渗硼、喷丸预变形后渗硼和氮-硼复合渗。试验结果表明:960℃和980℃渗硼的GH3535合金的表面硬度约700HV0.1,渗层深度为0.10~0.12mm;预变形后渗硼的GH3535合金的表面硬度稍低于单一渗硼的合金,约为650HV0.1,但渗层深度比单一渗硼的合金增加了约0.02mm;氮-硼复合渗GH3535合金的表面硬度与单一渗硼的合金相当,约为700HV0.1,渗层深度达0.16mm。     

Non-Hall-Petch hardness dependence in ultrafine fibrous MgAl2O4-MgO eutectic ceramics fabricated by the laser-heated floating zone (LFZ) method

MgAl₂O₄-MgO eutectic ceramics were fabricated by the laser-heated floating zone (LFZ) method with various growth rates to assess its possible beneficial effect on microstructural aspects and mechanical properties. It was determined that the growth rate optimizing the microstructure and mechanical properties is 750 mm/h; below this value, coarsening of the fibrous microstructure takes place with a degradation of these properties. In the extreme case of 50 mm/h growth rate, the presence of undesirable transverse cracks was unavoidable. Thanks to the high growth rate of 750 mm/h, ultra-fine fibrous microstructure MgAl₂O₄-MgO eutectic ceramics can thus be fabricated with greater hardness (15.5 GPa from Vickers indentation and 22 GPa from nanoindentation) and flexural strength (?345 MPa). It is reported that hardness scales with the interfiber spacing λ according to a law of the type lnλ/λ, contrary to the assumed Hall-Petch-like dependence. This proposed law can be explained in terms of dislocation hardening induced by the MgO fibers.     

Wear behavior of AISI D2 steel by enhanced ion nitriding with atomic attrition

An experimental study was performed to investigate the effect of atomic attrition on wear behavior of AISI D2 steel. Wear tests were conducted under three different loads (5, 10, and 20 N) and sliding speeds (100, 200, and 500 rpm), using ball-on-disk type tester and SiC ball. After wear test, the specimen nitrided with ion bombardment showed superior wear behavior. The enhanced hardness by ion bombardment could have a beneficial effect on increased wear resistance. In addition, a wider and more adhesive oxide layer formed on the worn surface of ion-bombarded specimen, because of the rougher structure on the surface by ion bombardment, could lead the surface to withstand wear for longer duration time, acting as a protective layer.     

高硬度常温干燥有机硅玻璃树脂的性能特征

介绍了有机硅玻璃树脂的基本性能特征,常温下干燥的高硬度有机硅玻璃树脂涂料的工艺生产简易过程,以及工艺技术性能指标和改性树脂的性能特征应用范围。     

改善胶乳三腔双囊胃管质量的生产工艺研究

以浓缩天然胶乳并用20份MG49天甲胶乳作胃管基础管身胶料可有效提高管身硬度和撕裂强度,并解决纯天然胶乳管身硬度不足、临床不易插管的难题,而对产品工艺性能及其他性能无不良影响。用"硝酸钙+工业酒精+表面活性剂"代替"硝酸钙+生粉附型剂+表面活性剂"作凝固体系,可改善胃管球囊胶膜厚度的均匀性。对胃管球囊内表面做适度氯化处理,可克服球囊与胃管管身产生的粘连或粘伤。适当改变绑线位置可有效减少胃管球囊胶膜出现的龟裂纹;球囊绑线处涂覆氯仿值二中~三中(见表9注)、总固体25%~35%的胶料3~4次,可获得较好涂胶效果。     

压裂液用绒囊暂堵剂实验研究

由于绒囊暂堵剂在钻完修井及煤层气勘探开发中的暂堵作用得到应用,本文针对绒囊暂堵剂在压裂暂堵方面进行研究;通过对绒毛剂、成膜剂、成核剂的筛选,选定0.3%的绒毛剂A、浓度超过0.1%成膜剂及0.3%成核剂6为优选的绒囊暂堵剂浓度及材料;并对绒囊暂堵剂与压裂液及压裂液添加剂配伍进行及破胶性评价,绒囊暂堵剂与压裂液及添加剂配伍并不影响压裂液冻胶的破胶性;通过细管摩阻实验发现绒囊暂堵剂比清水有更高的摩阻压差。